Way2call telephony device is your ultimate telephony integration solution! |
Line Polarity inversion for detect connect |
Post Reply |
Author | |
doronsh
Way2call Joined: Mar 16 2009 Status: Offline Points: 95 |
Post Options
Thanks(0)
Posted: Jan 22 2010 at 7:35am |
firmware update has been emailed to you.
|
|
Jos
Newbie Joined: May 20 2009 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
Thanks Doron, I'll wait for the firmware update. |
|
doronsh
Way2call Joined: Mar 16 2009 Status: Offline Points: 95 |
Post Options
Thanks(0)
|
The line reversal feature is not supported by the Hi-Phone Desktop Pro but not via the DLL and API's Weâ?Tll send you a firmware update that supports this feature, and instructions how you can test it.
|
|
Jos
Newbie Joined: May 20 2009 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
Hello Doron, I have received the pro units. How I can read line polarity status?. Is there any specific event to inform about this or I must read any modem flag? Thanks. (I am using drivers 2.00.95 and Multipe devices DLL API 1.05.04) |
|
Jos
Newbie Joined: May 20 2009 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
Hello Doron,
Sorry for the delay. Our customer says that yes, line polarity can indicate remote connect, but I cannot check it yet. We have ordered you some Pro units to check it at our office. Regards, |
|
doronsh
Way2call Joined: Mar 16 2009 Status: Offline Points: 95 |
Post Options
Thanks(0)
|
Analog lines are not providing accurate way to detect the answer or connect state, and therefore the method is based on audio on the line, voice, silence ,.etc,.. Currently this is not supported by any of the Hi-Phone products, however, the Hi-Phone Desktop Pro may be able to report the line polarity reversal event, but again, Iâ?Tm not sure if this feature designed for this purpose, and if the Telco line generates this line polarity reversal as soon as line is answered. Can you verify this? |
|
Jos
Newbie Joined: May 20 2009 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
Is there another method for detect this connected status without use speech/tone detector(more accurately)? Perhaps another Hi-Phone modem? Our customer wants to calculate this time and with speech/tone detector values have undesired fluctuations. Thanks Doron. |
|
doronsh
Way2call Joined: Mar 16 2009 Status: Offline Points: 95 |
Post Options
Thanks(0)
|
The Hi-Phone Desktop Lite doesnâ?Tt support line polarity reversal feature. This feature may be assist with Caller ID detection, but Iâ?Tm not sure if it can give the connected indication. |
|
Jos
Newbie Joined: May 20 2009 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
Hello all, I am currently detecting remote connection in outgoing calls using events for speech/tone detector. This method is quite imprecise and have problems when we connect with a silence destination. It is know that in many PSTN lines there is a polarity inversion when remote picks up that could be used to detect this connected status and will be more accurately that the last one. I have been testing whit SLIC_PolarityReversal member for struct that returns GetStatus function but it seems that always is set to 0. I am using dll api. Is there any method in Hi-Phone Desktop USB Lite to get this polarity status? Thanks. |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0.110 seconds.